Worldwide shipping cost via DHL, FedEx or UPS:
For one kit — $70.
For two kits and more — $45 for each kit.

Plug&Ride Kit for Sur-Ron Light Bee. Up to 30% more power оn standard 60V battery and up to 300% on 72V battery. Compatible with 2025 version. Installation guide.

Сonnection to the standard wiring instead of the factory controller. All systems (kickstand, fall sensor, throttle, and key) will work. Headlights, brake light, and turn signals on road versions also will work. You can use "Eco/Sport" switch to set it up two different power modes. But the speedometer on this switch will not work, this function will be performed on our On-board computer.

In the kit:

• Nucular controller P24F with the latest firmware for Sur-Ron.
• On-board computer with a mount for fork stem.
• CAN-wire 120 cm (47.2 inch) for On-board computer.
• Wiring with connectors for connecting to Sur-Ron.
• Phase wire extensions with bolts and nuts.
• Plastic adapter for mounting.

In stock.

Attention!
The firmware for a standard 60V battery is installed on the controller. If you have a more powerful battery, you need to change its settings in the Controller > Battery section and set other power modes in the Controller > Control Modes menu.

We also recommend adding the Universal thumb lever for regen (NUCTHR) to the kit.

Worldwide shipping cost via DHL, FedEx or UPS:
For one kit — $70.
For two kits and more — $45 for each kit.

Plug&Ride Kit for Talaria Sting MX3/MX4/MX5. Up to 30% more power оn standard 60V battery and up to 300% on 72V battery (for MX3/MX4). Installation guide.

On MX3 on stock 60V battery, you will get up to 8kW
On MX4 with Greenway 60V battery up to 12kW
On MX4 with SCUD 60V battery up to 8kW
On MX5 with Greenway 72V battery up to 15,2kW
On MX5 with SCUD 72V battery up to (test)

Сonnection to the standard wiring instead of the factory controller. All systems (kickstand, fall sensor, throttle, and key) will work. Headlights, brake light, and turn signals on road versions also will work. You can use the switch on the right side to set it up different power modes. The Talaria factory display replace by our On-Board Computer.

In the kit:

• Nucular controller P24F with firmware for Talaria.
• On-board computer with a mount for fork stem.
• CAN-wire 120 cm (47.2 inch) for On-board computer.
• Wiring with connectors for connecting to Talaria.
• Plastic adapter for mounting with bolts.

In stock.

Attention!
The firmware for a standard 60V battery is installed on the controller. If you have a more powerful battery, you need to change its settings in the Controller > Battery section and set other power modes in the Controller > Control Modes menu.

We also recommend adding the Universal thumb lever for regen (NUCTHR) to the kit.

Worldwide shipping cost via DHL, FedEx or UPS:
For one kit — $70.
For two kits and more — $45 for each kit.

Plug&Ride Kit for Talaria XXX and XXX Pro. Up to 30% more power оn standard 60V battery and up to 300% on 72V battery. Installation guide.

Сonnection to the standard wiring instead of the factory controller. All systems (kickstand, throttle, and key) will work. Headlights, brake light, and turn signals on road versions also will work. You can use factory switch to set it up two different power modes.

In the kit:

• Nucular controller P24F with the latest firmware for Talaria XXX.
• On-board computer with a mount for fork stem.
• CAN-wire 120 cm (47.2 inch) for On-board computer.
• Wiring with connectors for connecting to Talaria XXX
• Plastic adapters for mounting with bolts and nuts

In stock.

Attention!
The firmware for a standard 60V battery is installed on the controller. If you have a more powerful battery, you need to change its settings in the Controller > Battery section and set other power modes in the Controller > Control Modes menu.

We also recommend adding the Universal thumb lever for regen (NUCTHR) to the kit.

Worldwide shipping cost via DHL, FedEx or UPS:
For one kit — $70.
For two kits and more — $45 for each kit.

Plug&Ride Kit for Apollo RFN RS Road (L1E), RS Endurance (L1E), and Rally Pro versions. Max power 12kW on stock battery. Сonnection to the standard wiring instead of the factory controller. Stock front guard (your bike will look like the factory version). Headlights, brake lights, and turn signals on road versions will also work. You can use the switch on the left side to choose power modes. Installation guide.

In the kit:

• Nucular controller P24F with the latest firmware for Apollo RFN.
• On-board computer with a mount for fork stem.
• CAN-wire 120 cm (47.2 inch) for On-board computer.
• Wiring with connectors for connecting to Apollo RFN
• Plastic adapters for mounting with bolts and nuts

In stock

We recommend adding the Universal thumb lever for regen (NUCTHR) and Bluetooth module to the order.

Worldwide shipping cost via DHL:
For one kit — $70.
For two kits and more — ask.

Plug & Ride Kit for E Ride Pro SS 2.0. Сonnection to the standard wiring instead of the factory controller. Up to 13kW on stock battery. Installation guide.

In the kit:

• Nucular controller P24F with the latest firmware for E Ride Pro SS.
• On-board computer with a mount for fork stem.
• CAN-wire 120 cm (47.2 inch) for On-board computer.
• Wiring with connectors for connecting to E Ride Pro SS.
• Plastic adapter for mounting with bolts and nuts.

Preorder.

We also recommend adding the Universal thumb lever for regen (NUCTHR) to the kit.

Worldwide shipping cost via DHL:
For one kit — $70.
For two kits and more — ask.

Plug & Ride Kit for E Ride Pro SS 3.0. Сonnection to the standard wiring instead of the factory controller. Up to 13kW on stock battery. Installation guide.

In the kit:

• Nucular controller P24F with the latest firmware for E Ride Pro SS.
• On-board computer with a mount for fork stem.
• CAN-wire 120 cm (47.2 inch) for On-board computer.
• Wiring with connectors for connecting to E Ride Pro SS.
• Plastic adapter for mounting with bolts and nuts.

Preorder.

We also recommend adding the Universal thumb lever for regen (NUCTHR) to the kit.

Worldwide shipping cost via DHL:
For one kit — $70.
For two kits or more — $45.

Plug & Ride Kit for 79bike Falcon Pro. Plus 3000W of power on a standard 72V battery. The maximum power on the standard battery is 13kW.

Сonnection to the standard wiring instead of the factory controller. Nucular On-Board Computer will replace the 79bike factory display.

Attention! We have two versions of wiring:
1) Off-road version (the lighting equipment will not work).
2) Road-legal version (the lighting equipment will work).

In the kit:

• Nucular controller P24F with firmware for 79bike.
• On-board computer with a mount for a fork stem.
• CAN-wire 120 cm (47.2 inch) for On-board computer.
• Wiring with connectors for connecting to the 79bike.
• Plastic adapter for mounting with bolts.

In stock.

We also recommend adding the Universal thumb lever for regen (NUCTHR) to the kit.

Worldwide shipping cost via DHL, FedEx or UPS:
For one controller — $70.
For two controllers and more — $45 for each kit.

For the controller setup, you need an On-board computer or Bluetooth module. Manual.

Tech specs:

• max power 30kW
• max phase current 500A
• max battery current 350A
• max battery voltage 90V
• dimensions 205х98х50 mm
• weight 1440 g

In the kit:

• Сontroller P24F with compound potting and the latest firmware.
• CAN-wire 120 cm (47.2 inch) for connection to the On-board computer.
• Covers for battery and phase wires with screws — 2 pcs.
• Screws for M6 terminals of phase wires — 3 pcs.
• Screws for M6 terminals of battery wires — 2 pcs.
• Pins for crimping JWPF connectors — 22 pcs.
• JWPF 6P connector — 4 pcs.
• JWPF 8P connectors — 2 pcs.

Attention!
Wire for Hall sensors or Encoder is not included in the kit and is purchased separately. You can choose additional wiring in the "Accessories" section on the website

Important information:

• How to screw the wires to the controller. Torque 6Nm MAX for all screws.
• How to assemble the JWPF connector.
• Connection diagram of P24F controller.

For the controller setup, you need an On-board computer or Bluetooth module. Manual.

Features:

• 8-layer low inductance board design
• polymer solid electrolyte low ESR capacitors
• custom top-side cooling MOSFET
• hard anodized aluminum casing for direct cooling
• removable color heatsink

Tech specs:

• max power 15kW
• max phase current 250A
• max battery current 170A
• max battery voltage 90V
• dimensions 55x34x77 mm

To configure the controller, display statistics and parameters. The mount is compatible with all types of GoPro mounts. Manual

In the kit:

• On-board computer 2.0 with the latest firmware in English.
• GoPro fork mount.
• PHD 2.0 4P connector — 4 pcs.
• PHD 2.0 6P connector — 1 pcs.
• PHD 2.0 8P connector — 1 pcs.
• Pins for crimping — 26 pcs.

If you don't have a crimping tool need to order "Crimped wires for the Display".

In stock.

Read about the differences between versions of on-board computers here.

Also, you can add a USB wire for On-board computer for charging your gadgets (NUCUSB).

Lighting control controller. A controller designed to control turn signals, brake lights, headlights or LED strips. The board has three CAN inputs and can function as a CAN splitter. Manual.

In the kit:

• uLight controller with the latest firmware.
• PHD 2.0 4P connector — 4 pcs.
• PHD 2.0 6P connector — 4 pcs.
• Power wires 22AWG 2x200 mm with connectors XH 2.54 2P — 6 pcs.
• Power wires 22AWG 300 mm with pins, crimped on both sides — 8 pcs.
• Wires 26AWG 300 mm with pins, crimped on both sides — 20 pcs.

In stock.

We recommend adding a CAN wire for connection uLight to CAN-bus. Check in the Accessories section.

Module for configuring the controller via Android and iOS apps. It can be used instead of the On-board computer. It connects to the CAN-bus. If you order the controller and the module, a 1.2 meter long (47 inch) CAN wire (PHD-JWPF) for connection will be included in the controller. If, in addition to the module, the kit will include an On-Board computer, you need to order an additional CAN wire (PHD-PHD) from the “Accessories” section. Manual

Tech specs:

• Two CAN ports
• Power supply 8-15V
• Bluetooth 5.0
• Android, iOS
• Size 50x18x9 mm
• Weight 5.2g

In the kit:

• Bluetooth module
• Protective soft case

In stock

Wire for connection to the CAN-bus of the On-board computer, uLight, BMS and other devices from Nucular. Crimped on both sides with PHD 2.0 6P connectors. Three different lengths.

Attention!
Not suitable for connecting a Controller P24F to other Nucular devices. For this purpose, use the CAN wire PHD-JWPF.

Wire for connection to the CAN-bus of the Controller P24F. Crimped from one side with PHD 2.0 6P connector and JWPF 6P on the other. Three different lengths.

Attention!
The PHD-JWPF CAN wire 120 cm (47.2 inch) long is supplied with the Controller P24F. If you ordered a controller, you do not need to order a CAN wire separately.

Wire for throttle and brake input for Controller P24F. JWPF 6P connector on the controller side and two JWPF 3P connectors on the other side. Wires 22AWG. Length with connectors 28 cm (11.02 inch).

This wire is required if you connect all peripherals directly to the Controller P24F, and not to the On-board computer (default connection).

You can also purchase a mating part for this wire, see "Mating part TH/BK".

JWPF 3P connector on one side and stripped wires on the other. The wires are 22AWG. Length with connectors 23 cm (9.05 inch). Included 2 pcs.

JWPF connectors on one side and stripped wires on the other. The wires are 22AWG. Length with connectors 17 cm (6.7 inch). Included 6 pcs.

Kit for connecting the Controller P24F to the standard Sur-Ron Light Bee wiring.

If you ordered the Kit for Sur-Ron Light Bee, you do not need to order these wires separately.

ABS plastic adapter for installing the Controller P24F on the Sur-Ron Light Bee.

In the kit:

• Plastic ABS adapter with mounts.
• Mounting screw kit.
• Phase wires extensions with heat shrink and bolts for connection.

Attention!
If you ordered the Kit for Sur-Ron Light Bee, you do not need to order this adapter separately.

Kit for connecting the Controller P24F to the standard Talaria Sting MX3/MX4/MX5 wiring.

If you ordered the Kit for Talaria Sting, you do not need to order these wires separately.

Factory quality ABS adapter for installing the P24F controller on the Talaria Sting.

In the kit:

• Plastic adapter with mounts.
• Mounting screw kit.

Attention!
If you ordered the Kit for Talaria Sting, you do not need to order this adapter separately.

Kit for connecting the Controller P24F to the standard Talaria XXX wiring.

If you ordered the Kit for Talaria XXX, you do not need to order these wires separately.

Factory quality ABS adapter for installing the P24F controller on the Talaria XXX.

In the kit:

• Plastic adapters with nuts.
• Mounting screw kit.

Attention!
If you ordered the Kit for Talaria XXX, you do not need to order this adapter separately.

Wire extensions with bolts and nuts. For connection P24F controller to stock motor of Sur-Ron Light Bee. Also suitable as extension cords when installing the ChiBattery 72V on the Talaria XXX.

In the kit:

• Tree wires.
• Bolts and nuts.

On one side a JWPF 8P connector for connecting to the Controller P24F, on the other side there is a waterproof 8P connector. Wires 22 AWG. Length with connectors 29 cm (11.4 inch).

Attention!
The mating part for the connector is not included, you can purchase it separately. Part number DJ7081Y-2.3-11.

On one side a JWPF 8P connector for connecting to the Controller P24F, on the other side there is a waterproof 6P connector. Wires 22 AWG. Length with connectors 29 cm (11.4 inch).

Attention!
The mating part for the connector is not included, you can purchase it separately. Part number DJ7061Y-2.3-11.

For connecting multiple Controllers, BMS or other Nucular devices to a CAN bus. 4 ports, PHD 2.0 6P connectors. Dimensions 16x22 mm.

30V, opto-isolated, used when connecting a powerful load to the controller (stop lights or fans).

Wiring diagram for brake lights and fans.

Wires for soldering, 12 pcs. Wires 26 AWG. Length 20 cm (7.87 inch). Crimped with pins on both sides.

By default, all control devices (thumb throttle, brake levers, switches, etc.) are connected to the ports located on the back of the On-Board Computer. To access, you need to unscrew five screws and remove the plastic cover. For connection, PHD 2.0 connectors and crimp pins are used, which are included in the kit. If you do not have a crimping wire tool, for example, SN-2549, you can use these crimped wires

It is necessary to cut them in the middle, solder them to the wires of the throttle or brake handles, and insert the crimped ends into the PHD 2.0 connectors (include in the kit of On-board computer) and connect them to the On-board computer.

Temperature sensors NTC10k B: 3950 for electric motor. Includes 2 pcs.

The wire is 40 cm (15.74 inch) long. It is crimped with a PHD 2.0 4P connector for connection to the On-board computer in the THR (throttle) or BRK (brake) ports.

For 24F and P24F controllers. Wires 10AWG. Length with connectors 55 cm (21.65 inch). XT90E-M connector on one side, two 8-6S terminals on the other.

In the kit:

• Cable with connectors.
• Cap for XT90E-M connector.
• Two screws with nuts to secure the cap.

Length with connectors 22 cm (8.66 inch). Crimped with PHD 2.0 4P connector. Connects to the USB port on the back side of the On-board computer 1.0 and 2.0.

In the kit:

• PHD 2.0 4P connector — 4 pcs.
• PHD 2.0 6P connector — 4 pcs.
• Power wires 22AWG 2x200 mm with connectors XH 2.54 2P — 6 pcs.
• Power wires 22AWG 300 mm with pins, crimped on both sides — 8 pcs.
• Wires 26AWG 300 mm with pins, crimped on both sides — 20 pcs.

Attention!
If you have already ordered a uLight controller, then you do not need to buy this set separately, it will be included.

Board for the QS138 motor, which allows you to switch to an ABZ + PWM encoder for 1024 pulses.

In the kit:

• Encoder board.
• Wires with connector.
• Two magnets of different thicknesses.
• Plastic adapter for installation.

Video installation guide. Connection diagram

Capacitor block for connecting the solar panel to the controller and charging the ebike battery using MPPT technology and motor charging function. To use the module, you need to update the controller firmware to v0.8.12 and higher.

To connect the module to the 24F and P24F controllers, you can purchase a Wire for charging (code NUCTHMW).

For version 2.0. Shockproof plastic. In case of damage to the case of the On-Board Computer, you can replace the entire case yourself.

In the kit:

• The rear part with a button and an SD card cap.
• Cover for connection ports for the rear part.
• Front part with glass.
• Buttons and button pushers.
• Screws for assembling — 7 pcs.

Read about the differences between versions of On-board computers here.

For version 2.0. Transparent plastic. To replace damaged glass on the On-board computer. Attaches with double-sided tape (included). The screen has a protective film that can be removed after installation.

Read about the differences between versions of On-board computers here.

For versions 1.0 and 2.0. To replace a damaged On-board computer LCD module. To replace it, disconnect the LCD module cable from the PCB and unsolder two contacts of the damaged LCD module.

Kit with mounting and connectors for On-board computer version 1.0 and 2.0. Compatible with GoPro mounts.

In the kit:

• Mounting for the fork stem.
• PHD 2.0 4P connector — 4 pcs.
• PHD 2.0 6P connector — 1 pcs.
• PHD 2.0 8P connector — 1 pcs.
• Pins for crimping for 26 AWG wire— 26 pcs.

If you don't have a crimping tool need to order "Crimped wires".

Attention!
If you have already ordered an On-board computer, then you do not need to purchase this items, it will be included in the kit.